Mechanical Systems > Pumps

Pumps

Course Number: 735

The Pumps textbook explains how pumps are used and the principles of their operation. It covers a wide variety of pumps, including reciprocating pumps and various kinds of rotary pumps. A lesson on special-purpose pumps describes diaphragm pumps and pumps used for corrosive and abrasive materials. The final chapters deal with the maintenance of pumps, including the replacement of packing glands, seals, and bearings.

Does your curriculum require additional topics not included in this textbook?  Build a customized version of the Pumps textbook below.

This textbook has been recently updated
to include topics lists, objectives, & key terms for every chapter.

Recommended Contact Hours – 15

Preview a Chapter

Preview a Chapter

  • Table of Contents
  • My Custom Book
  • Exam Copies
  • Suggested Titles

Table of Contents

Chapter 1: Uses of Pumps

Topics: Development of pumps; Pumping systems; Water, chemical, waste, high-viscosity, and solids pumping systems

Learning Objectives:

  • Describe dead-end and recirculating hot water distribution systems.
  • List several special considerations involved in chemical pumping systems.
  • Define the term viscosity and give examples of high-viscosity materials.
  • Tell the effects of heat on the pumping of high-viscosity materials.
  • List some special problems involved in the pumping of solids.

Chapter 2: Pump Hydraulics

Topics: Terminology; Calculating total head, horsepower, and available vs required NPSH; Pump performance; Head capacity; Efficiency; Horsepower curves; Pump selection

Learning Objectives:

  • Describe suction head and suction lift pumping conditions.
  • Tell what three elements make up total dynamic head.
  • Define static suction head.
  • Contrast liquid, brake, and electrical horsepower.
  • Tell what useful information can be gained from pump curves.

Chapter 3: End-Suction Centrifugal Pumps

Topics: Operation; Part definitions; Casing materials; End-suction casing configurations; Impeller types; Wearing rings; Shafts, bearings, and sleeves

Learning Objectives:

  • Describe the function of the following: pump casing, shaft, impeller, wearing rings, and stuffing box.
  • Contrast frame-mounted and close-coupled end-suction pumps.
  • Give characteristics of fluids pumped with open, semi-open, and closed impellers.
  • Name an advantage and a disadvantage each for stainless steel and brass shaft sleeves.

Chapter 4: Propeller and Turbine Pumps

Topics: Line-shaft, can, and submersible turbines; Flow patterns; Axial- and mixed-flow propeller pumps; Turbine pump construction and applications

Learning Objectives:

  • Explain the construction of a line-shaft turbine pump.
  • Name the two types of flow possible in a propeller pump.
  • Tell the function of diffuser vanes in an axial-flow propeller pump.
  • Define electrochemical corrosion and state its cause.
  • Describe fluids that can be pumped by a regenerative turbine pump.

Chapter 5: Rotary Pumps

Topics: External-gear, internal-gear, lobe, screw, vane, rotary piston, and flexible-member pumps; Rotary pump installation

Learning Objectives:

  • Describe the fluids that can be pumped by a rotary pump.
  • Explain the operation of external- and internal-gear pumps.
  • Describe the parts and construction of a lobe pump.
  • Compare and contrast timed and untimed screw pumps.
  • Tell why sealed bearings might be used in a vane pump.

Chapter 6: Reciprocating Pumps

Topics: Reciprocating pump applications, parts, classification, and operation; Horizontal and vertical plunger pumps; Air-driven pump operation

Learning Objectives:

  • Name the parts that make up the power end of a reciprocating pump and describe their operation.
  • Define the terms single-acting pump and double-acting pump.
  • Compare simplex and duplex pumps.
  • Explain how the pumped fluid lubricates a reciprocating pump.
  • Calculate the discharge pressure of an air-driven pump when given the piston ration and motor air supply.

Chapter 7: Metering Pumps

Topics: Uses and classes of metering pumps; Plunger, piston, diaphragm, air-operated, and rotary metering pumps

Learning Objectives:

  • Tell what kinds of pumps are used for metering applications.
  • Describe metering pump lubrication techniques.
  • Name the parts of a diagram metering pump and state the function of each.
  • Explain the operation of a diaphragm metering pump.

Chapter 8: Special-Purpose Pumps

Topics: Handling difficult materials; Chemical, magnetic-drive, canned-motor, slurry, pulp-handling, trash, sewage, diaphragm, and vortex pumps

Learning Objectives:

  • Describe the operation of a flexible-tube pump.
  • Give an application for a progressing-cavity pump.
  • Name one disadvantage of a seal-less magnetic-drive pump.
  • Explain how to prepare a new centrifugal pump for operation.
  • Tell which parts of a reciprocating slurry pump require the most maintenance.

Chapter 9: Packings and Seals

Topics: Sealing requirements; Stuffing boxes; Packing materials and recommendations; Installing packing; Mechanical, cartridge, balanced, and special seals

Learning Objectives:

  • Tell why slight leakage through shaft seals is necessary.
  • Name the type of stuffing box required for pumps operating under suction lift conditions.
  • Give a typical application each for cotton, Teflon", and aluminum packing.
  • Describe the procedure involved in replacing pump packing.
  • Describe a packingless seal.

Chapter 10: Pump Maintenance

Topics: Pump bearings, lubrication, and seals; Pump installation and maintenance; Centrifugal, turbine, rotary, and reciprocating pump maintenance

Learning Objectives:

  • Name three types of antifriction bearings.
  • Name three factors to consider when preparing pump lubrication schedules.
  • Describe a typical application for each of the following bearing seals: felt, leather, synthetic.
  • Tell the two major maintenance problems encountered in rotary pumps.
  • Explain how to identify worn piston rings in a reciprocating pump.

Add Chapters to Your Custom Book

Select Chapter(s):

  •    Chapter 1: Uses of Pumps
  •    Chapter 2: Pump Hydraulics
  •    Chapter 3: End-Suction Centrifugal Pumps
  •    Chapter 4: Propeller and Turbine Pumps
  •    Chapter 5: Rotary Pumps
  •    Chapter 6: Reciprocating Pumps
  •    Chapter 7: Metering Pumps
  •    Chapter 8: Special-Purpose Pumps
  •    Chapter 9: Packings and Seals
  •    Chapter 10: Pump Maintenance

My Custom Book

    Create a custom book that contains only the training content that your students need to succeed

    Our topics cover a broad and diverse spectrum of subject matter, from reading blueprints to electrical schematics, measurement to rigging and safety, material handling to welding, and everything in between! Choose only the lessons that meet your specific curriculum requirements.

    Request Exam Copies

    Exam Copies

    Ready to see a copy of our textbooks? After selecting which textbooks you’d like to review for your course, you can submit your request by either logging in or creating an account so we know where to ship your exam copies. A representative from Schoolcraft will contact you to confirm and finish processing your request.

    Exam copies are always free and yours to keep.

    Selected Exam Copies

      none selected

      * Maximum of five copies can be ordered


                    





         





      750 W. Lake Cook Road, Buffalo Grove, Illinois 60089   ●   Phone: 800.837.1255   ●   © 2018 Schoolcraft Publishing, a TPC Training Company